Skip to main content

Canon Service Tool V3400 for resetting waste ink tank counter


Canon Service Tool V3400 allow you to reset the printer waste ink counter.


It solves the message "waste ink tank full" or leds orange et green blinking 8 times on these Canon printers:
  • Canon Pixma iP2700, iP4800, iP4810, iP4840, iP4900, iP4910, iP4940, iP4970, iP4980, iP4990, iP5810, iP5880
  • Canon Pixma MP230, MP270, MP280, MP490
  • Canon Pixma IX6500, IX6510
  • Canon Pixma IP3600
  • Canon Pixma PRO9000
  • Canon Pixma MG2120. MG2140, MG2240, MG3140, MG4140, MG5140, MG5240, MG5340, MG6140, MG6240, MG8140, MG8240

Where to find the Service Tool V3400 ?

Here is a paying version:
It should be possible to find a free version, but check the link for any trojan or virus.


How to use Service Tool V3400 ?
  • Unzip the file.
  • Set the printer in Service Mode:
- Power OFF the printer by Power button.
- Connect the printer with USB cable to the PC.
- Press and hold Resume button (red triangle in the red circle) and press Power button
- Hold both buttons until power on indicator will light then release Resume button (dont release Power button) and press Resume button 5 times
- Release all buttons (the printer will blink few times with green light and will then light green constantly).
  • Run the Service Tool V3400.exe program.
  • Select the connected USB port number from USB PORT
  • In the Ink Absorber Counter section of the Service Tool, select MAIN from the Absorber pull-down menu.
  • From the Counter Value (%) pull-down menu, select the value (in 10% increments) which is the closest to the actual counter value confirmed before replacement of the logic board, and click SET
  • Error 002
  • Error 006

Comments

Unknown said…
Do not bother following the link to the site to purchase the reset tool. I have already tried purchasing this tool and after takingmy money, I received an e-mail with a binary file which my AV says is suspicious and removes it. You DO NOT get a zip file containing the program which they allegedly say you pay for. DO NOT be conned as I have been. Oh and by the way, an e-mail to their `SUPPORT` yields no results either. Stay well away from this program
Anonymous said…
if you paid by c/card raise a charge back with your c/card provider. Non receipt of advertised product.

Popular posts from this blog

How to fix error B200 on canon Printers

MAJ11/06/17 Error B200 means the printhead voltage or temperature is not normal. The Printhead could be defective.... but first, try these solutions below: Solution 1 : Disconnect the power cable from the printer. Wait 1 hour. Connect the power cable Solution 2 : Check and Clean Head contact pin condition of the carriage unit Check Cable connection especially the carriage FFC Solution 3 : Turn off the power Open the panel Turn on the power Wait for print carriage to start moving to the left. Let it go past half way Before print carriage reaches left hand side shut the cover. Leave the Printer turned on Solution 4 : Unplug the power cable. Open the printer Push the whole print head mechanic to the center While the printer still open, plug the power and turn it ON.  When the printhead still moving and is going to the very LEFT, close the cover.  Wait until its boot up.  Solution 4a: Take out all of the ink cartridges Lift up the gr

How to solve error code 006 with Canon Service Tool V3400

MAJ 25/08/17 The Service Tool V3400 allow to reset the counter of some Canon printers. For the error code 006 , try this : Solution 1: Check your cartridges: an empty cartridge can lead to error 006 Solution 2 : After you avec clicked on "Main", wait a few minutes.  If the error still here, restarts the Service Tool Solution 3 : Close the service tool Disconnect the USB cable from the printer After 10 seconds, plug back the cable to the printer On Windows, click next when appears "New device" Open the service tool

How to solve error B204 on Canon Maxify printers

The error B204 could happen after a cartridge replacement. First of all, when installing, remove the cartridges from the plastic package, but do not drill any plastic membranes, as this will cause this error when placing the cartridge. The error may also appear if you change a completely empty cartridge: when installing a full cartridge, the printer enters a cleaning cycle, but the printhead has not yet received ink from the newly inserted cartridge. Here are some tips to cancel this error B204:: Solution 1: Remove the cartridges Power the printer for 2 minutes Switch on the printer Install the cartrdiges Solution 2: Switch on the printer Unplug  the power cable Open the cover Move the print head carriage manually to the usual place where it goes for the cartridge change (If the printhead carriage is not movable, reconnect and then turn on the printer, then unplug it again when the head carriage is in the moving position). Change the cartridges. Close the fr