Skip to main content

Canon MP287 with error code E08



This error (or error code 5B00) appears with this message: “The Ink Absorber is Almost Full

To solve this problem, you have to reset the waste ink counter.


Solution:
  • Turn on the printer.
  • The panel will display error E08, with message “The Ink Absorber is Almost Full”. 
  • Download the Resetter for MP287 
  • Printer must be in a state of Service Mode. 
  • Turn off the E08 error by pressing the power button. 
  • Do not unplug the power cord. 
  • Press and Hold the button Stop/Reset followed by pressing the Power button. 
  • Release the button Stop/Reset only.
  • Press the button Stop/Reset 6 times, then release both buttons simultaneously.
  • The printer MP287 will be in Service Mode. 
  • LCD Panel will blank / dark and in your computer will detect new hardware. Ignore it. 
  • Exctract and Run Service Tool for MP287 
  • Click on “Play”, then the printer will proceed and will print one page with the words “D = 000.0″ 
  • Click “Clear EEPROM”. Then click “EEPROM”, and the printer will print the results Resetter. Writing one line as follows: “TPage (COPY TTL = 00 000 = 00 000)”. 
  • Turn off by pressing the power. 

Comments

seaverock said…
Where does the Play Button be located at the service tool
Anonymous said…
SALAMAT PO... MORE POWER
Anonymous said…
hoho Ano po password nung Service Tool? hindi ko po kasi ma-run

Popular posts from this blog

How to fix error B200 on canon Printers

MAJ11/06/17
Error B200 means the printhead voltage or temperature is not normal. The Printhead could be defective.... but first, try these solutions below:


Solution 1:
Disconnect the power cable from the printer.Wait 1 hour.Connect the power cable
Solution 2:
Check and Clean Head contact pin condition of the carriage unitCheck Cable connection especially the carriage FFC
Solution 3:
Turn off the power Open the panel Turn on the power Wait for print carriage to start moving to the left.Let it go past half way Before print carriage reaches left hand side shut the cover. Leave the Printer turned on
Solution 4:
Unplug the power cable.Open the printerPush the whole print head mechanic to the centerWhile the printer still open, plug the power and turn it ON. When the printhead still moving and is going to the very LEFT, close the cover. Wait until its boot up. 
Solution 4a:
Take out all of the ink cartridgesLift up the grey bar by where the ink goesLeft the print head in the middle of the pr…

Error 6000 or P03 on Canon printers

MAJ11/06/17
Error code 6000, P03 or E23 is a line feed error. It also should be flashing 3 times for this error on the on/off button.

You can have this error on these Canon printers: MP140, MP150, MP160, MP190, MP210, MP220, MP170, MP180, MP450, MP460, MP240, MP250, MP260, MP270, MP480, MP500, MP510, MP520, MP530, MP830, MP540, MP620, MP550, MP560, MP600, MP610, MP630, MP800, MP810, MP830, MP970, MP980, MG2100, MG3100, MG4100, MG5100, MP640, MP990, MG5200, MG5300, MG6100, MG6200, MG8100, MG8200,


Solution 1:
Verify that the paper tray is correctly set.If any object is placed in front of the machine, remove it.
Solution 2:
Search for any small pieces of paper in the printer, or a tiny object.
Solution 3:
Power off the printerWait 5 minutePower on. 
Solution 4:
Clean the encoder strip with a soft clothSolution 4a:
Clean the printhead
Solution 5: one of these parts could be faulty:
Timing sensor unit QM2-2683Timing slit disk film QC1-6229Feed roller ass'y QL2-0925Platten unit QM2-2923Logic board…

Error U052 on Canon printers

MAJ 14/10/14
Error U052 appears on these Canon printers: MX850, MP540, MP530, MP600, MP610, MP970 and others...

Message error: The type of print head is incorrect install the correct print head U052



Solution 1:
Remove and replace the cartridges.
Solution 2:
Insert new cartridges
Solution 3:
Reseat the print head to correct print issues or clear error.
Solution 3a (thanks to Tony LeBaigue):
Remove the ink cartridges.Remove the printhead: cleaned the rear contacts with a cotton bud and surgical spirit.Left the part 5 minutes to dry.Install the printhead and the cartridges. The printer wil be into printhead clean mode and will return to normal mode.
Solution 3b (thanks to Arjen - Canon MP610):
Power off the printer. Press and hold both selection buttons underneath the screen, and switch on the printer. After a long start up the 'copy' screen appeared, and it printed a copy of a sheet.
Solution 4:
Clean the printhead
Solution 4a:
The print head is broken and it must be changed by a new one…