Skip to main content

Posts

Showing posts from April, 2011

How to fix error F14 on Toshiba copiers

This error appears on these products: e-studio 160, e-studio 166, e-studio 163, e-studio 203 ... Solution 1 : Turn off the  copier Hold down the key's "0", "8" and start the copier.   After that it will apper (AD) or (ADJ), entrer "389" and press the start key. Then turn off the copier and turn it on again.     Solution 2: If the problem persist, replace the NV-RAM module

Fixing Error 13.xx on HP Laserjet

3.XX PAPER JAM [LOCATION] Media is jammed at the specified location (and possibly at other locations). If the message persists after all jams have been cleared, a sensor or sensor lever might be stuck or broken.  For all jam messages, do the following:  1. Remove jammed print media from the specified location. Check the entire paper path for other pieces of media in the path.  2. Open and close the top cover to clear the message.  3. Check sensors and flags in the paper path for proper operation. 3.0 PAPER JAM [LOCATION] A non-specific paper jam occurred.  1. Remove jammed media from the specified location.  2. Verify the paper tray is fully closed.  3. Inspect and/or replace the feed and separation rollers.  4. Ensure there is no obstruction in the path, such as a torn piece of paper.  5. Open and close the top cover to clear the message.  6. Check sensors and flags for proper operation. 13.1 PAPER JAM OPEN INPUT TRAYS Paper-delay jam at paperfeed area.  1. Ensure

Fixing error U072 on Canon printers

Solution 1: Open the cover Remove the cartridges. Power off the printer Power on the printer Réinstall the cartridges Close the cover. Solution 2 :   Verify that the ink tank are installed in the appropriate positions. Change the faulty cartridge Solution 3 : Clean the printhead

How to solve error code "13.10.00" on HP printers laserjet and Business inkjet

Solution 1 : Take a stiff folder and cut it to 5" accross and feed it up the channel first on the left side and then on the right side. Odds there is still a shred of paper in the paper path. Solution 2 (13.10.00 Jam inside duplexer/left door): A jam has occurred in the reversing area. The leading edge of the media did not reach the reversed paper sensor in the duplexer within the required time.  Open the cover and remove the jam from the indicated area.  Close the door and allow the printer to attempt to clear the jam.  Remove the duplexer and check for any obstructions in it.  Clean the duplex rollers .  Check the diverter for any damage.  Replace the duplexer. Solution 3 (13.10.00 Jam inside left or lower left door.): The page from the turnaround path did not reach the duplexer-jam sensor,SR1.  Open the left side door and remove the jam.  Remove the duplexer and check the duplexer-jam sensor, SR1 for correct functionality.  Check for paper or other obstructi

Fixing error code oxc18a0206 on HP printers

This error appears on these printers: C7180, C7280,  C5180, C6150, Photosmart 3310, etc... Solution 1 : Press * and # at the same time Press 1, 2, 3 and “support R0632M” should display Press > and “information menu” should display Press > and “configuration menu” should display Press OK and “hardware failure status” should display Press OK “failure status: clear”. Press OK to clear Press CANCEL Press CANCEL Press CANCEL Turn printer off, unplug power cord for 2 minutes, plug cord back in then turn printer back on. Solution 2 : Without turning off the product, disconnect the USB cable from the rear of the product. Remove the cartridges from the product. Wait for the ' Insert Cartridges ' message to display on the control panel. Disconnect the power cord from the back of the product. Wait 60 seconds. Reconnect the power cord. If the product does not automatically turn on, press the Power button ( ). Reinsert the cartridges, and then close any open do

How to reset waste ink tank for a Canon Bubble jet I965

Solution: Turn off printer To enter Service Mode: Hold down resume then press power button. Keep hold of power and release resume. Press resume twice. Wait for printer to stop ftzing. You should now have solid green but if you get 1 green and 8 orange lights alternating press resume once. You should now have a solid green: you're in Service Mode Press the resume button 4 times. You should now have a solid green.  Press the power button to register the reset.  Press the power button once more to switch off.  Press the power button to switch on again. It's ok.

Fixing Error Code 241 Paper Jam on Lexmark printers

Solution 1: - Take tray out. - Lift up so have access to bottom of printer. - The 2 rubber rollers in the middle can be taken off - Flip them inside out and put them back on and put tray back in. Solution 2 : Take out paper tray 1. Remove any jammed sheets of paper you find there. Once you have done this, reinstall the paper tray and try printing again. If the printer jams again with a 241 Paper Jam error message, look to see if it has tried to feed a sheet of paper out of the tray.    If paper is not leaving the tray and no paper appears to be jammed anywhere in the printer, remove paper tray 1 once again. Make sure the paper is loaded correctly in the tray. With the tray removed, you can also check the feed/pick rollers. Do the following: Look into the printer where the tray goes. Look for two tan-colored rubber rollers (circled in green in the picture below). These are the rollers that grab and feed the paper up into the printer.   Clean off the rollers

Fixing error code 0xb9000009165, 0xb9000009 on HP printers

Message looks like: Error 0xb9000009 165hw interrupt hwv2.c is Problem with the HP printer Solution 1: - Uninstall all the HP drives and software - Unplugg the USB cable from the printer - Unplugged power supply from the outlet and printer - Plugg the USB back in to printer - Unplugg the power supply from the power module. - Plugg the power supply cord to module - Plugg the power supply in to outlet - Plug the power module connector to printer. Solution 2: - Unplugg the power and usb cable from the printer - Download and install the lastest drivers and software for the printer - Plugg the power and then the USB.