Skip to main content

Error P,7 P7 or P07 (5B00) on Canon printers


Solution 1: If the device is not functioning properly or to clear memory, reset it.
  • On the operator panel, press the button. (The display will go blank.) Note: It may be necessary to unplug the power cord if pressing the ON button does not shut off the printer.
  • Wait approximately ten seconds and then press the button again.
  • Wait until the device has completed its cycling process before submitting another job request. Note: It may be necessary to unplug the power cord and retry if the above steps do not clear the error.

 

Solution 2:
Step 1: Entering Service Mode

  • While the printer is OFF, press and hold the Start/Stop button (Resume/Cancel in some other models).
  • While holding the Start/Stop button, press and hold the POWER button.
  • When the POWER LED (green light) lit, release the Start/Stop button (still holding the POWER button).
  • Press the Start/Stop button TWICE (still holding the POWER button)
  • Release the POWER button.
  • Wait for the LCD to display “0″ (zero).

Step 2: Using Resetter / Software

  • Download Ressetter: http://www.ziddu.com/download/10241255/ServiceTool_1050.zip.html
  • Run “service_tool 1050.exe”.
  • Confirm detected USB-port numbers on USB port column.
  • Click “Main button” on Clear ink counter section. Make sure there are papers in the paper feed because the printer will print after the process is complete.
  • Click “platen button” on the “Clear ink counter” section. The printer will print again.
  • Turn off the printer and then turn the printer on. You printer is ready for use.

Comments

pr said…
I'd already make all of these recommendation but after running service_tool 1050.exe and clicking the main button, nothing happened. So can you please help me? is there another software resetter that resolve this P07 and 5B00 error code. Thanks for your helps
About Me said…
yeah...me too... many times tried no works... any other solution?
Unknown said…
in the second solution..
after i press the stop/reset button the panel did not change to 0... any idea?
Anonymous said…
Hi. Follow the link below. This should fix your problem.
http://www.youtube.com/watch?v=D_JaIrmxFvM

I solved it this way. smartkasio[at]gmail[]com
Anonymous said…
Complete shit.Video is too blurry to see anything.

Popular posts from this blog

How to fix error B200 on canon Printers

MAJ11/06/17 Error B200 means the printhead voltage or temperature is not normal. The Printhead could be defective.... but first, try these solutions below: Solution 1 : Disconnect the power cable from the printer. Wait 1 hour. Connect the power cable Solution 2 : Check and Clean Head contact pin condition of the carriage unit Check Cable connection especially the carriage FFC Solution 3 : Turn off the power Open the panel Turn on the power Wait for print carriage to start moving to the left. Let it go past half way Before print carriage reaches left hand side shut the cover. Leave the Printer turned on Solution 4 : Unplug the power cable. Open the printer Push the whole print head mechanic to the center While the printer still open, plug the power and turn it ON.  When the printhead still moving and is going to the very LEFT, close the cover.  Wait until its boot up.  Solution 4a: Take out all of the ink cartridges Lift up the gr

How to solve error code 006 with Canon Service Tool V3400

MAJ 25/08/17 The Service Tool V3400 allow to reset the counter of some Canon printers. For the error code 006 , try this : Solution 1: Check your cartridges: an empty cartridge can lead to error 006 Solution 2 : After you avec clicked on "Main", wait a few minutes.  If the error still here, restarts the Service Tool Solution 3 : Close the service tool Disconnect the USB cable from the printer After 10 seconds, plug back the cable to the printer On Windows, click next when appears "New device" Open the service tool

How to solve error B204 on Canon Maxify printers

The error B204 could happen after a cartridge replacement. First of all, when installing, remove the cartridges from the plastic package, but do not drill any plastic membranes, as this will cause this error when placing the cartridge. The error may also appear if you change a completely empty cartridge: when installing a full cartridge, the printer enters a cleaning cycle, but the printhead has not yet received ink from the newly inserted cartridge. Here are some tips to cancel this error B204:: Solution 1: Remove the cartridges Power the printer for 2 minutes Switch on the printer Install the cartrdiges Solution 2: Switch on the printer Unplug  the power cable Open the cover Move the print head carriage manually to the usual place where it goes for the cartridge change (If the printhead carriage is not movable, reconnect and then turn on the printer, then unplug it again when the head carriage is in the moving position). Change the cartridges. Close the fr